Customer Reviews (4639)

Parts were all there, no warping and assembled very well! Very pleased with this Heldrake model!

Good casting. Small amount of sanding and cleanup but less then half the price of the workshop

Very minor flash and mold slip. The top of the hull has some minor cupping (easy to fix with hairdryer). There a raised curve on the top that's thin and delicate (in front of the hatch - I might replace it with a strip of plastic card). Mine requires some gap filling around the rear hull piece, thankfully this is easily accessible. No issues with the sides, tracks, small pieces, cannon. I had to use a razor saw to cut the casting channels off the top hull piece (this is covered by the rear hull plate.. they're chunky). Overall, great value. I would say this level of modeling work is what I've come to expect of most resin kits. Probably a little more than an average item from this site, but still a good cast. Only comes with 2 side sponsons (current rules allow for 4). Looks better with 2 in my opinion, just tell your opponent it has 4.

Great cast. Used it to make a custom Lord Solar (requires a larger base).

I haven't assembled these but the casts are great. Very difficult item to find online. If you've been searching (for your vulture gunship) -- this is your solution!

Great casts.

Some flash on these. While the unit is useful and the cast seems good for the price, I don't enjoy working on these at all from a hobby perspective. Very fiddly. The ribbons are annoying. Nothing against the cast quality or company... just be mindful that these might frustrate you too.

Great cast. No issues. Use reddit for instructions.

Better cast than what you get in finecast. Light clean up and warping on exarch guns. Easy stuff.

Great cast. Easy to assemble (instructions on reddit)

Great casts. Very easy to assemble.

These require some clean up. The back hull extension may have a slight curl downward (will get in the way of the engine part) -- press the lower section into the top while using a hairdryer and it's easy to match the correct angle. There is a mould channel that connects under the back lip of the rear hull extension (in the round cut-out at the far back). This was tricky to clean up. A blade didn't work very well. I ended up using a dremel and carefully ground it clean. The kit comes with heavy weapons (which you should have several of from other kits as well). I highly recommend magnetizing the contact points and outer armor plates. Overall, great cast and easy build. I magnetized the bases (used golf tees and ~1cm dia magnets... there isn't a great flat spot on the bottom of these... use strong super glue)

Mild flash (clean by scratching with a blade and sanding with foam sanding sticks). Easy to assemble. Use a hairdryer or warm water to straight on the vertical support. I built two in about 15 mins.

Good cast. Super straightforward to assemble and base.

A little trickier than the scorpion super heavy tank kit, the hull had some delamination towards the front tips. There's some clean-up under the cannon, just right of the cockpit. The rear fin that connects to the back of the hull had some shrinkage. Nothing insurmountable, but this is more in line with what resin kits are usually like. A little filler to fix the delaminating. Foam sanding sticks are useful too. Note the hull has a little bit of a cup (upward convex shape... whereas the scorpion has the normal concave shape like falcons). Looking at online photos, this appears correct. It has a slightly different shape than other Eldar vehicles.

Gem of a kit to build. Great cast. Only the slightest warp on the turret barrels. Took 30s with a hairdryer to fix.

Shipping took some time, but considering the distance it was faster than expected. The model itself is the same quality if not better than Forge World.

une première commande passée au mois de juin.
envoie lapide, propre et bien protégé.
seulement une tête as un défaut, je me signal par mail , sans reponse

a ma seconde commande je le signal sur paypal pour éventuellement en avoir une dans l'envoi, sans réponse et je leur signal a nouveau dans le ticket de paiements sans réponse encore . et a réception pas de tête supplémentaire . domage

THIS IS AN EXPERT KIT!
Do not attempt to build this if you aren't able to use heat to fix warped parts and have green-stuff / milliput to fix gaps. Some mold slip but cleaned up fairly well. Instructions for this thing are hot garbage. you will need to find instruction videos via the red you watch site.

Reason I give it 5 star is because of the price, and similarity to FW resin, this model went well enough together.

This was tough. I ended up not being able to save this model, all my parts were warped like crazy and I just cant recommend this to anyone. Ended up dashing the body and keeping only the turret, but even then most of it needed alot of clean up. 2 out of 10.